PORSCHE 924 GT CHECK OUTCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 356 1950-59 - Body (includes uncategorized and accessory items) 99334703104 If your outer tie rods are worn, you will experience sloppy steering response and knocking / creaking sounds. Your outer tie rods keep the steering centered, so failure can be dangerous and can seriously affect steering control. After replacing the tie rods, you will experience tighter, more precise feedback without noise. Tie rod consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Inner axial joint 1 qty. Lock nut 1 qty. Dust bellows / boot we recommend replacing the right and left side tie rods at the same time. Sold individually. 2 necessary per car.
$227.10
Make a selection 99642101000 No need to buy the entire shaft assembly any longer. Simply replace your worn out piece with our inexpensive high quality flex disc.
$114.35
Make a selection 99663114380 Please note: this is for cup / r models up to 2001. They have the cut out for the clear headlight corner trim. All motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis and do not carry any warranty. No exceptions.
$335.50
Make a selection 99750598390 This is a genuine 997.1 GT3 Porsche motorsports cup spoiler lip. It is a cost-effective replacement for the original GT3 spoilers. It also improves front end downforce. Please be aware that it is lower than the original Porsche spoiler but is far more pliable and more curb friendly. This part is shipped in a smaller box by motorsports to conserve on shipping costs. It is manufactured in polyurethane, so it has memory. Once you receive it just lay it out in the sun for an few hours or slowly and carefully warm it up with a heat gun. Please note: all motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangea...(choose a part on the right to read more)
$239.95
Make a selection 9A160410400EQ If your starter is on its way out, you will notice an intermittent clicking noise and a delay in the vehicle starting. Eventually, you will hear a metallic screeching noise that is a sure sign that your starters bendix mechanism, bearings or solenoid are kaput. When ordering a new starter, be sure to check the protection cap on the terminal for cracks which allows moisture in and causes pre-mature failure. High-quality denso OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
$531.30
Make a selection BEC996002TTSR Brombacher exclusive covers are completely manufactured in the south of Germany in baden wurtemberg, between stuttgart and our local mountains in the southern black forest. The materials chosen is environmentally friendly production and each stich is made with care. 100% Germany quality, perfect, personalized appearance for every taste, even in the covered state a mixture of cotton and polyester nano-coated on the outside which makes it so dirt and water repellent, completely paint-friendly, with very breathable construction. Price includes: cover color selection, color selection of trim, custom embroidered logo and a matching bag with a small custom logo, in the same colors. Please let us know what model, year...(choose a part on the right to read more)
$832.76
Make a selection AP9972TT170 The stock exhaust of the Porsche 997.2 turbo is very restrictive compared to aftermarket systems. Porsche does this to meet sound and emission purposes like most OEM manufacturers. agency power set out to create an exhaust system for the new Porsche 997.2 turbo 6speed or pdk that did not drone, would produced amazing performance, and under throttle give an incredible sound. we have accomplished this! the new agency power exhaust not only saves about 30lbs off the rear end, it also improves power quite a bit.
$3,937.45
Make a selection BEC993001GSOH Brombacher exclusive covers are completely manufactured in the south of Germany in baden wurtemberg, between stuttgart and our local mountains in the southern black forest. The materials chosen is environmentally friendly production and each stich is made with care. 100% Germany quality, perfect, personalized appearance for every taste, even in the covered state a mixture of cotton and polyester nano-coated on the outside which makes it so dirt and water repellent, completely paint-friendly, with very breathable construction. Price includes: cover color selection, color selection of trim, custom embroidered logo and a matching bag with a small custom logo, in the same colors. Please let us know what model, year...(choose a part on the right to read more)
$917.07
Make a selection BEC911930BB Brombacher exclusive covers are completely manufactured in the south of Germany in baden wurtemberg, between stuttgart and our local mountains in the southern black forest. The materials chosen is environmentally friendly production and each stich is made with care. 100% Germany quality, perfect, personalized appearance for every taste, even in the covered state a mixture of cotton and polyester nano-coated on the outside which makes it so dirt and water repellent, completely paint-friendly, with very breathable construction. Price includes: cover color selection, color selection of trim, custom embroidered logo and a matching bag with a small custom logo, in the same colors. Please let us know what model, year...(choose a part on the right to read more)
$832.76
Make a selection BEC9972GT3RS Brombacher exclusive covers are completely manufactured in the south of Germany in baden wurtemberg, between stuttgart and our local mountains in the southern black forest. The materials chosen is environmentally friendly production and each stich is made with care. 100% Germany quality, perfect, personalized appearance for every taste, even in the covered state a mixture of cotton and polyester nano-coated on the outside which makes it so dirt and water repellent, completely paint-friendly, with very breathable construction. Price includes: cover color selection, color selection of trim, custom embroidered logo and a matching bag with a small custom logo, in the same colors. Please let us know what model, year...(choose a part on the right to read more)
$877.80
Make a selection BES91105000S This muffler was specifically designed for a backdate to the st look. It is manufactured for mid-range and top end performance, all without drone inside the cabin. It seamlessly mates to ssi heat exchangers for added performance while keeping the cabin warm in the winter. The muffler is vastly different than the common baffle plated mufflers stuffed with packing material that are common in the aftermarket. Ours are uniquely made with double perforated sound absorption tubes based on the halbgegenstromprinzip (half counter current principle). The acoustic silencer absorption tubes are made in a trapezoidal pattern and are perforated with varying diameters, which isolate and dampen the unwanted frequencies that c...(choose a part on the right to read more)
$2,759.30
Make a selection BEC996001SR Brombacher exclusive covers are completely manufactured in the south of Germany in baden wurtemberg, between stuttgart and our local mountains in the southern black forest. The materials chosen is environmentally friendly production and each stich is made with care. 100% Germany quality, perfect, personalized appearance for every taste, even in the covered state a mixture of cotton and polyester nano-coated on the outside which makes it so dirt and water repellent, completely paint-friendly, with very breathable construction. Price includes: cover color selection, color selection of trim, custom embroidered logo and a matching bag with a small custom logo, in the same colors. Please let us know what model, year...(choose a part on the right to read more)
$917.07
Make a selection BES99105060S - + 12 crank hp & + 12 crank torque - 2 3/4 tubing (70mm) straight through design for max. Power - weighs 18 lbs. (8.5 kg), which is a 3 lbs. Savings off of OEM center muffler. - replaces stock side mufflers and stock center muffler. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 2 x 3.5 (90mm) round tips. - includes all necessary clamps and mounting brackets. - made in Germany. - intoxicating cup car growl at idle, partial throttle and wide open throttle. - no dme programming necessary, does not alter emissions, 50 state legal in the u.s. Our 991 GT3 center muffler replacements are vastly different than the baffle plated mufflers stuffed with packing that are common in the after...(choose a part on the right to read more)
$2,454.38
Make a selection BES98115001SK This is our jekyll and hyde version ! The perfect compromise for you and your loved ones. Rich, deep race car tones with the valves open and soft subtle, completely stock sounds with them closed. Top of the line or range depending on the english, and is the best choice for a daily driver. + 11 hp & + 10 tq gain. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - 2 1/2 tubing (63.5 mm). - 2 x 3.5 (90 mm) round tips. - intoxicating growl at idle, partial throttle and wide open throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - minimal resonance / drone in the cabin (200 rpms worth) compared t...(choose a part on the right to read more)
$5,457.38
Make a selection BES9811000S Facts: - long tube race headers with motorsports merge collector. - catalytic bypass for race use. - 2 1/2 tubing (63.5 mm). - primary diameter 45mm outer , 42mm inner - reduces thermal stress on the motor. - made in Germany please add 2 engine to header gaskets when ordering - 2 qty 997 111 107 31 our latest development for the 981 is aimed at those who are looking for more torque in the mid-range and horsepower up top. These headers are ideal for those who are tracking their cars.
$3,603.60
Make a selection BES981C1200SGT4 - equal length long tube headers with motorsports merge collector. - 200 cell hd German hjs tri metal sport cats. - primary diameter 50mm outer , 47mm inner for the larger 3.8l displacement. - t316 lightweight stainless steel. - reduces thermal stress on the motor. - made in Germany by m&m exhaust gmbh. Please add 2 engine to header gaskets when ordering - 2 qty 997 111 107 31 power: - 981 GT4 / spyder (3.8l) = + 18 crank hp (13kw) & 16 crank torque ( 21 nm) our latest development for the 981 is aimed at those who are looking for more torque in the mid-range, a rich, deep exhaust growl. These headers contain the latest hjs cats, they are nicknamed "hd" for high durability matrix design catalytic converters. T...(choose a part on the right to read more)
$6,069.53
Make a selection BES981C5000SKGT Gt4 clubsport ++ with the valves open. Completely civilized at low rpms and while cruising. + 11 hp & + 10 tq gain. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - 2 3/4 tubing. - 2 x 3.5 (90 mm) round tips. - intoxicating growl at idle, partial throttle and wide open throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - minimal resonance / drone in the cabin. - "aero quip" style motorsport muffler connections to ensure a leak free exhaust. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. Please note: gaskets a...(choose a part on the right to read more)
$5,630.63
Make a selection BES98215000S The open architecture of this muffler allows for a deeper four-cylinder turbo tone, with plenty of whistling on tap. Coming off throttle from higher rpms exudes a chorus of snarling, gurgling and crackling letting everyone know that this car is not your average 982. + 15 hp & + 12 tq gain. - 2 x 3.5 (90 mm) round tips. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - lower deeper tones than the factory exhaust with far more whistling and gurgling / crackling off throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - no drone in the cabin. - "aero quip" style motorsport muffler connections t...(choose a part on the right to read more)
$3,535.46
Make a selection BES987C0200SHD Brombacher Cayman/s (sound version) stainless steel exhaust system facts: - + 20 crank hp & + 19 crank torque - 200 cell high flow, tri metal German hjs sport catalysts - 2 tubing (50 mm) straight through design for max. Power - weighs 57 lbs. (25,8 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability - dual 3.5 (90mm) round tips - includes quick release clamps - made in Germany - intoxicating growl at idle, partial throttle and wide open throttle - no dme programming necessary. FVD is proud to introduce our newest line of Brombacherexhaust systems. Brombacher exhausts are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredibl...(choose a part on the right to read more)
$8,968.08
Make a selection BES987C02F0S "brombacher" 987-2/s (sound version) stainless steel exhaust system
$7,791.63
Make a selection BES99110200SK "brombacher" stainless steel exhaust system with valves for the 991 + 25 hp & + 20 tq gain. - 200 cell hjs "hd" sport catalysts. - 25 lb. Weight savings over OEM system (weighs 59 lbs. (27,0 kg), OEM weighs 84 lbs. (38kg). - 2 3/4 tubing (70mm). - 4 x 3.5 (90mm) round tips. - motorsport merge collector. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - "aero quip" style motorsport connections without gaskets or flanges to ensure a leak free exhaust. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - under load (moving) with valves closed: 85db* - under load (movin...(choose a part on the right to read more)
$10,532.45
Make a selection BES99105040S Perfect muffler for those looking for a more aggressive exhaust note without changing the factory catalytic converters. The added benefit is you can reuse your OEM catalytic converters for emissions purposes. + 15 hp & + 12 torque - reuses OEM cats, perfect for those concerned about warranty. - open muffler design for added power. - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 4 on a scale of 1-10 in volume (1 being stock) below 3,000 rpms, 6 on a scale of 1-10 in volume under maximum load (3 being stock). - includes cone and v band style hardware to prevent exhaust leaks. - made in Germany. - modular desi...(choose a part on the right to read more)
$3,066.53
Make a selection BES99110200SK1 "brombacher" stainless steel sound switch exhaust system complete for the 991 3,4l. + 25 hp & + 20 tq gain. - 200 cell hjs "hd" sport catalysts. - 25 lb. Weight savings over OEM system (weighs 59 lbs. (27,0 kg), OEM weighs 84 lbs. (38kg). - 2 3/4 tubing (70mm). - 4 x 3.5 (90mm) round tips. - motorsport merge collector. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - "aero quip" style motorsport connections without gaskets or flanges to ensure a leak free exhaust. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. Please note: the 991 Carrera s (us or canadian model) comes standard with valves! Power...(choose a part on the right to read more)
$10,034.64
Make a selection BES99115000S + 11 hp & + 10 tq gain. - 2 3/4 tubing (70mm). - 4 x 3.5 (90mm) round tips. - net weight is 16.4 kg / 36 lbs. (10 lb savings over stock 3.4 l mufflers) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - 90 db maximum (oem muffler is 75 db for reference). - replaces OEM side mufflers and connects to OEM header and catalytic flange. Please note: this muffler does not include exhaust valves and is meant to replace the OEM system on the base 3.4l 991 (2012+). Power is stated at the crank. This is the very 1st aftermarket muffl...(choose a part on the right to read more)
$4,063.29
Make a selection BES99115000SKR + 11 hp & + 10 tq gain. - 2 3/4 tubing (70mm). - 18 lb. (8.5 kg)weight savings over OEM center muffler. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - replaces OEM center muffler and connects to OEM header and OEM side mufflers and OEM tips. Please note: this muffler is a direct replacement the 991 Carrera s (3.8l - us model) which comes standard with valves. It is also a direct replacement for the Porsche sport exhaust option. This center muffler bypass for the 991 is one of the most technically advanced for Porsche t...(choose a part on the right to read more)
$3,899.28
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |